You are Here:
Battle of Breakneck prize table rifle build thread.

Author (Read 5186 times)

Battle of Breakneck prize table rifle build thread.
« on: April 09, 2016, 12:02:46 PM »
 

TS Customs

  • Moderator
  • Target Painter
  • *****
  • 19
    Posts
  • Karma: 1
  • FNG
I had the opportunity recently to put together a prize table rifle for the Battle of Breakneck PRS shoot in Broadwater, NE April 15-17.
It's awesome how the industry can come together in support for one of the fastest growing precision rifle sports!
Parts consist of a BigHorn TL2 action, J Allen Enterprises chassis, Hawk Hill 6.5mm Marksman contour barrel, Huber Concepts 2 stage trigger, and Hawkins Precision rings and muzzle brake.

The last of the parts showed landed here Wednesday afternoon 4/6/16. After unboxing everything I snapped a couple pictures pre-assembly to show you what we're working with.

We prepped the barrel for coolant Wednesday evening and were ready to tear into this thing Thursday morning.

Barrel dialed in at the throat with a long stem indicator to ensure a square transition for the bullet from the case to the bore.

Program for a BigHorn TL2 Standard bolt face receiver loaded in the controller, G54 Z zero established, and we're rolling!
I need a windshield wiper installed on this inside of the machine door I think....

Tenon major diameter of 1.062" verified, offsets are good to go.

45 degree chamber chamfer profiled for a smooth entry of the cartridge into the chamber.

Threads cut and incrementally stepped down .001 per pass until a snug yet smooth thread fit is achieved. Flood coolant and high RPM's result in some beautiful threads! I've found the BigHorn receiver threads to be cut extremely square with zero taper.


A custom taper body drill is used to rough the chamber out on the majority of the short action standard bolt face cartridges we do. Runs at 1200 rpm and .012" feed per rev. Sure speeds up the chambering process when the roughing cycle takes 15 seconds!!!
Sorry, you don't get to see detail on that tool at this time :)

Finish from the body drill... I've got about 150 chambers on this one and the finish looks as good as a chamber reamer.

6.5 Creedmoor TacMatch is the cartridge of choice for this one. Throated shorter than saami spec, factory ammo is still safe to use and it remains possible to use the longest 140 class bullets and have them seated inside of mag length.
Use of a hydraulic holder with a positive stop allows us to keep track of the tool length offset for all the reamers in the inventory and be able to pop them in and out, input the proper offset, and go without having to touch tools off.

Did I mention I need a windshield wiper?

The primary chambering cycle is ran leaving the chamber .010"-.020" short of proper headspace. From there, a depth to proper headspace is calculated and input into a finishing program and the remainder is cut to final headspace.
1.022" is what we're looking for at GO +.002" with this receiver.
 
A light polish with 600grit and oil evens up the chamber finish and gives a little bite to the brass to ease the bolt thrust.

The barrel is then torqued up to the receiver, witness mark established at top dead center, and removed again for finishing the muzzle. The muzzle end of the bore is dialed in, 11 degree crown cut, and 5/8-24 threads are spun on. After peeling a few thousandths off the shoulder to time the brake up, a small diameter carbide boring bar is used to bore the brake open to .020" over bullet diameter to assure concentric clearance around the bullet's path. I then use a program written with local macro variables to turn the muzzle brake diameter concentric to the outside diameter of the barrel and apply a decorative dished crown to the brake. A quick deburr on the ports and the brake will get spin polished to the barrel to make that seem invisible.

Over to the mill the barrel goes to receive the maker's name and caliber designation.

Beings this barreled action is going to be riding in a chassis, there is no stock fitting required and the barreled action is ready for paint.
Having a vinyl cutter and proper design software allows us to spruce stuff up now and then!


After laying down a base of Gun Metal Gray and brief cycle through the oven, the artwork was applied, and a layer of Tungsten gray was applied to the artwork and remaining pieces for some contrast. This concluded the first day's work on the rifle. Not bad for one day!

First thing Thursday morning, the metal parts were pulled from the oven and assembly commenced!


To say that I'm thrilled with how this rifle turned out would be an understatement. You better all have your rifles working and your best shootin' pants on next weekend because I wouldn't mind bringing this thing back home with me!!!



I want to thank all my industry affiliates who donated parts for this rifle. I also want to thank the crew at Battle of Breakneck for allowing TS Customs the opportunity to put them all together.

I look forward to seeing everyone next week! Good luck!
 

Re: Battle of Breakneck prize table rifle build thread.
« Reply #1 on: April 09, 2016, 12:10:18 PM »
 

Jeff M

  • Paint Removal Specialist
  • Administrator
  • Steel Ringer
  • *****
  • 703
    Posts
  • Karma: 100
    • Road To PRS
That looks AWESOME, and I sure wouldn't mind it coming home with me!  Here's hoping...   LOL
Every time you make a typo, the errorists win.
 

Re: Battle of Breakneck prize table rifle build thread.
« Reply #2 on: April 09, 2016, 02:33:58 PM »
 

Colohunter

  • Target Painter
  • *
  • 33
    Posts
  • Karma: 0
    • Black Rifle Blog
That looks awesome!
 

Re: Battle of Breakneck prize table rifle build thread.
« Reply #3 on: April 12, 2016, 12:16:56 AM »
 

XC700116

  • Target Painter
  • *
  • 45
    Posts
  • Karma: 0
  • FNG
Beautiful Work
 

Re: Battle of Breakneck prize table rifle build thread.
« Reply #4 on: April 12, 2016, 11:05:17 PM »
 

cjwise5

  • Target Painter
  • *
  • 6
    Posts
  • Karma: 0
Holy crap nice work! That thing looks amazing.
 

Re: Battle of Breakneck prize table rifle build thread.
« Reply #5 on: April 18, 2016, 03:57:27 PM »
 

OilFieldTrash16

  • Target Painter
  • *
  • 15
    Posts
  • Karma: 0
  • FNG
Extremely nice rifle, so who was the lucky winner? Any pics to share of them enjoying the grand prize?
 

Re: Battle of Breakneck prize table rifle build thread.
« Reply #6 on: April 18, 2016, 04:41:36 PM »
 

Jeff M

  • Paint Removal Specialist
  • Administrator
  • Steel Ringer
  • *****
  • 703
    Posts
  • Karma: 100
    • Road To PRS
Griz won it.  There are pics floating around somewhere, I'll see if I can grab one.
Every time you make a typo, the errorists win.
 

Re: Battle of Breakneck prize table rifle build thread.
« Reply #7 on: April 18, 2016, 08:49:39 PM »
 

Colohunter

  • Target Painter
  • *
  • 33
    Posts
  • Karma: 0
    • Black Rifle Blog
That was a beautiful gun! It looked and felt even better in person!